Wall Ties/Structural Repair
Triton's wall ties are manufactured from stainless steel to avoid corrosion and are either mechanically fixed, resin bonded or a combination of both. Mechanically fixed replacement cavity wall ties are most suited to structures of known strength on both the inner and outer skin. When the strength is unknown, resin bonded replacement cavity wall ties are most suitable.
In addition to replacement wall ties, lateral restraints and crack stitching rods, Triton also offers a range of resins, grouts and drill bits to facilitate installation. See below for further details or speak to your local Triton technical sales representative.
- ER10 - Expanding Resin Tie
- Triton Dryfix
- Triton RR10 - Double Adhesive Tie
- AA10 - Double Adhesive Tie
- Triton Helical Resin/Spiro Remedial Tie
- Triton EE10 - Single Fix Double Expansion
- Triton SS10 - Single Fix Double Expansion
- Triton Lateral Restraint
- Tribar Reinforcement Rods
- Trifix Adhesive
- TriGrout Extra
- Triton Repair Mortar
- TriSet Polyester Resin
ER10 - Expanding Resin Tie
The ER10 is a 10mm diameter replacement cavity wall tie that combines 304 grade austentic stainless steel and neoprene. The ER10 is most suited to situations where the outer leaf is of a solid construction and the inner leaf is of a weaker material (blockwork) as the inner end of the tie is resin bonded into the structure, and the outer end is expanded to form a fix.
Supplied in boxes of 200.
A helical dry fix replacement wall tie for use where both outer and inner leaf is of good sound quality. Quick and easy to install, the one-piece Dryfix tie requires no resin, grout or mechanical expansion. Suitable for pinning masonry features, it can be used in bricks, blocks, concrete, hard mortar and timber. The Dryfix tie can be installed through insulation without affecting thermal performance. Manufactured from stainless steel.
RR10 - Double Adhesive Tie
The RR10 is a 5mm diameter stainless steel replacement wall tie that can be used in situations that require both the inner and outer wall to be anchored with resin. The RR10 is a 5mm stainless steel bar with a 10mm nut on each end of the tie with a centre drip. The RR10 is manufactured from 304 grade austentic stainless steel. Once the resin has cured, a pull test on the inner leaf can be performed using the appropriate adaptor and testing machine. Typical loads achieved are in excess of 2.5kn.
Supplied in boxes of 250.
A high quality 10mm stainless steel tie for use in situations that require both the inner and outer wall to be anchored with resin. The ‘waisted’ ends give the tie a mechanical and an adhesive fixing once the resin is applied. Suitable for use in brick, lightweight block, timber and mortar. The AA10 tie is available in lengths to suit varying cavity widths and construction types. An inbuilt feature enables load tests to be carried out on site on the inner leaf if necessary.
Triton Helical Resin/Spiro Remedial Tie
An economical helical replacement wall tie which is resin fixed at both ends. Installation is fast and effective using Trifix Resin.
Supplied in 400ml cartridges.
Triton EE10 - Single Fix Double Expansion
Manufactured from stainless steel and Neoprene, the 11mm EE10 tie features a torque nut which sets both the inner and outer expanders independently. The EE10 tie is particularly suitable for brick or stone structures where there is a sound inner leaf and in constructions of four stories or less. Can be pull tested.
Triton SS10 - Single Fix Double Expansion
The SS10 can be used in similar applications to the EE10 tie, but, because of its brass components, will also satisfy the fire safety requirements of constructions which are more than four stories high. Can be pull tested.
Triton Lateral Restraint
Typically used to stabilize old or bowed walls, Triton’s Lateral Restraints are manufactured from 8mm diameter 304 austenitic Stainless Steel rods. They are available in a standard 1m length but can be supplied in other lengths on request. They are designed to restrain the whole of the brick outer structure to the floor joists. Installation involves minimal disturbance to the homeowner as they are fitted from the outside of the property.
Supplied in 400ml cartridges.
Tribar Reinforcement Rods
Stainless steel Tribar Rods are designed to stabilise existing masonry and are used in general crack stitching repairs, to reinforce masonry above failed lintels, as a method of overpinning to reduce the underpinning load and to re-tie solid or cavity masonry panels. Typical applications will be in buildings with shallow foundations or which are subject to movement, masonry arches and bridge repairs.
Tribar Rods are available in lengths of 1m, 3m or 7m and should be bedded in or bonded with TriGrout Extra.
Trifix is a two component epoxy resin system specifically formulated for use with twin component side by side cartridges using either hand operated or, more normally, air operated guns, using "at the nozzle" static spiral mixers. Trifix is colour coded for visual assurance that the two components are fully mixed. The product is solvent free, thixotropic, ie will not readily slump, and cures in cold, damp conditions. Trifix is formulated as an anchoring adhesive to give a strong, stress-free joint within the structure, be it brick, stone, mortar or timber.
Supplied in 400ml cartridges.
TriGrout Extra is designed to be used as a structural grout for the bedding and bonding of stainless steel reinforcement bars. A two component product, TriGrout Extra is supplied in plastic buckets containing all the powder and liquid needed to make up the product. Trigrout Extra is shrinkage compensated, non-gassing and thixotropic. It is suitable for use with hand or powered applicators and available in two sizes (to make 3 litres or 6 litres of grout).
Triton Repair Mortar
A pre-packed modified cement based repair mortar for use with concrete, render and screed repairs. Use with Triton LPA/Primer as both a primer to the repair area and as a gauging solution for mixing the Triton Repair Mortar and to enhance the flexural strength of the mix.
Typical areas of use would include repairs to honeycombed concrete, leaking construction joints (Triton Quick Set also required), spalled concrete and repairs to screeds and renders.
Available in 10 kg packs.
TriSet Polyester Resin
Triton Tri-Set is a very fast setting, two part, grout/adhesive supplied in a twin cartridge containing the base polyester resins and hardener which are mixed through the static mixing nozzle on application. Typical uses include the permanent installation of wall ties. It provides a waterproof, chemical and vibration proof bond. Tri-Set offers excellent adhesion, high strength and is corrosion resistant.
Supplied pre-packed ready for use in twin cartridge (resin 380ml, hardener 150ml).